Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
| Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung | ||
|
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2017/11/15 16:15] Alexandra Thiel [Querschnittswerte] |
— (aktuell) | ||
|---|---|---|---|
| Zeile 1: | Zeile 1: | ||
| - | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ||
| - | ====== Module „CLT-Plate 1D - Internal forces“ ====== | ||
| - | |||
| - | {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:gesamtcs.png?600 |CLT-Plate 1D - Internal forces}} | ||
| - | ===== Input data ===== | ||
| - | |||
| - | The input is divided into: | ||
| - | |||
| - | * definitions of the cross section | ||
| - | * specifications concerning structural fire design | ||
| - | * internal forces according to the theory (of 1<sup>st</sup> or 2<sup>nd</sup> order) on which the calculations are based on | ||
| - | * design factors | ||
| - | * specifications concerning stability | ||
| - | ==== Cross section ==== | ||
| - | |||
| - | See [[modul_plate1d_continuousbeam#querschnitt|Module CLT-Plate 1D - Continuous beam]] | ||
| - | ==== Fire ==== | ||
| - | |||
| - | See [[modul_plate1d_continuousbeam#brand|Module CLT-Plate 1D - Continuous beam]] | ||
| - | ==== Type of calculation, internal forces, design factors and specifications concerning stability ==== | ||
| - | |||
| - | The internal forces and the underlying type of calculation are defined in the tab „Internal forces, stresses and utilisation ratios“. Additionally, the design values are specified here. | ||
| - | |||
| - | If the internal forces result from a calculation based on a first order analysis a substitute buckling length has to be stated in case of a negative normal force ("problem of stability"). Based on this buckling length and the respective cross section the required buckling factor k<sub>c</sub> needed for the verification is calculated automatically. | ||
| - | |||
| - | {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:angabencsverification.png |Input - internal forces, design factors and specifications concerning stability}} | ||
| - | ===== Results and output ===== | ||
| - | |||
| - | ==== Cross section values ==== | ||
| - | |||
| - | See [[modul_plate1d_continuousbeam#querschnittswerte|Module CLT-Plate 1D - Continuous beam]] | ||
| - | === Zusammenfassung der Ergebnisse === | ||
| - | |||
| - | In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ werden die Spannungsverläufe sowie die maßgebenden Ausnutzungsgrade angezeigt. | ||
| - | |||
| - | {{ clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:ergebnissecsverification.png?600 |Zusammenfassung der Ergebnisse}} | ||
| - | ==== Ergebnisse im Detail ==== | ||
| - | |||
| - | Über den Button „Details“ können die Spannungen und Ausnutzungsgrade der einzelnen Schichten betrachtet werden. | ||
| - | |||
| - | {{ clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:detailscsverification.png?600 |Ergebnisse im Detail}} | ||
